Results 1 to 13 of 13
Thread: , 100%
Hybrid View
-
4th October 2007 10:01 #1Registered User
Join Date: Oct:2007
Location: Chicago
Posts: 14
, 100%
U-, 100%. . . :
Last edited by bambuchata; 4th October 2007 at 10:06.
-
4th October 2007 10:06 #2
PIO. . PIO DMA.
-
4th October 2007 10:14 #3Registered User
Join Date: Oct:2007
Location: Chicago
Posts: 14
-
4th October 2007 10:19 #4
-
4th October 2007 10:23 #5
-
4th October 2007 10:50 #6
:

"Windows XP PIO DMA . Windows XP DMA . , DMA , :
1. .
2. Windows .
3. DMA Windows XP .
O PIO ."
-
4th October 2007 11:20 #7
, - PCI ( .. 2 / ) ... ? ,
..Last edited by zizirixo; 4th October 2007 at 11:30.
| . | |
Dell CoftiFlex | Intel i5 3570 | 2x8GB DDR3 | 240GB SSD + 500GB HDD | RX580 4GB | Powered by 240V and a lot of coffee |
-
4th October 2007 11:54 #8
-
4th October 2007 19:15 #9Registered User
Join Date: Oct:2007
Location: Chicago
Posts: 14
1 IDE . Maxtor Segate, . /master/ 100%. PIO . , . 4 .
/slave/ , . 4 15 .
IDE DVD /master/ CD /slave/. DMA .
, ,
, ? Device Manager IDE PIO mode . DMA, .Last edited by bambuchata; 4th October 2007 at 20:55.
-
5th October 2007 01:20 #10Registered User
Join Date: Mar:2005
Location:
Posts: 58
- IDE .
-
5th October 2007 03:37 #11
-
5th October 2007 07:17 #12
.
http://sniptools.com/tipstricks/gett...-in-windows-xp
the http://support.microsoft.com/default...&Product=winxp
, . , sorryAn alternate, less-aggressive policy is implemented to reduce the transfer mode (from faster to slower DMA modes, and then eventually to PIO mode) on time-out and CRC errors. The existing behavior is that the IDE/ATAPI Port driver (Atapi.sys) reduces the transfer mode after any 6 cumulative time-out or CRC errors. When the new policy is implemented by this fix, Atapi.sys reduces the transfer mode only after 6 consecutive time-out or CRC errors. This new policy is implemented only if the registry value that is described later in this article is present.To implement the alternate behavior (reducing the transfer mode after six consecutive time-out or CRC errors instead of after six cumulative time-out or CRC errors), you must modify the registry as described below after you apply the hotfix.
WARNING: If you use Registry Editor incorrectly, you may cause serious problems that may require you to reinstall your operating system. Microsoft cannot guarantee that you can solve problems that result from using Registry Editor incorrectly. Use Registry Editor at your own risk.
Follow these steps, and then quit Registry Editor:
1.Click Start, click Run, type regedit, and then click OK.
2.Locate and then click the following key in the registry:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControl Set\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}\0001
3.On the Edit menu, point to New, and then click DWORD Value.4.Type ResetErrorCountersOnSuccess, and then press ENTER.
5.On the Edit menu, click Modify.
6.Type 1, and then click OK. Follow these steps, and then quit Registry Editor:
1.Click Start, click Run, type regedit, and then click OK.
2.Locate and then click the following key in the registry: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControl Set\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}\0002
3.On the Edit menu, point to New, and then click DWORD Value.
4.Type ResetErrorCountersOnSuccess, and then press ENTER.
5.On the Edit menu, click Modify.
6.Type 1, and then click OK.
Note The numbered subkeys that are listed earlier correspond to the primary and secondary IDE channels on a computer that contains a single IDE controller. If your computer contains two IDE controllers, the numbered subkeys for the primary and secondary IDE channels for each of the two controllers may be:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControl Set\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}\0002
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControl Set\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}\0003
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControl Set\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}\0004
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControl Set\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}\0005
To verify that you have located the correct subkey, verify that the DriverDesc value for the subkey contains the string value "Primary IDE Channel" or the string value "Secondary IDE Channel."The holiday was fun-packed,
The contract, still intact




Reply With Quote


windwos 10
5th May 2023, 00:01 in Windows