Results 1 to 9 of 9
Thread: Maxtor N40P
Hybrid View
-
28th May 2008 08:13 #1Registered User
Join Date: May:2008
Location: Stara Zagora
Posts: 13
Maxtor N40P
! . , . ( Maxtor-a ) . BIOS- , , fail. ( Maxtor Powermax 4.22), . , . . ? .
-
28th May 2008 09:13 #2
-
28th May 2008 09:51 #3
SA (service area) -80% SA+ . - , ,
2 HDD -
-
28th May 2008 10:04 #4
-
28th May 2008 21:00 #5Registered User
Join Date: May:2008
Location: Stara Zagora
Posts: 13
. 100 -200 .( ). . ?
-
28th May 2008 23:20 #6
-
29th May 2008 00:19 #7Registered User
Join Date: May:2008
Location: Stara Zagora
Posts: 13
Samo . . , . . . , - - , ... .. ! . , , , " " - firmware-a. PC3000 ( firmware), . 14- . . - .
[bg]eto go i pyrwiq problem - sled startirane na [/bg] pcmx_pkr [bg] harddiska se razpoznawa (wqrno e towa za razwyrtaneto - trqbwa da se spre zahranwaneto), sledwa da se izbere standarten revim, pri kojto ]e se opita da pro`ete sluvebnata informaciq. To`no tuk gyrmi - kazwa, `e ne moveda zaredi sluvebnata informaciq (tablica li kwo be[e...).
Move da se izbere i zarevdane na [/bg] ldr [bg] fajl, no sled kato mu podam fajla toi ni]o ne prawi. Specialno za tazi operaciq widqh w dokumentaciqta kym [/bg] pc3000 [bg], `e NE trqbwa da e w [/bg] safe mode.
:
1. Drive start without setting the safe mode jumper.
That method will work if during the utility launch the drive is identified by its factory alias and the safe mode
jumper is disabled. The essence of that method consists in loading just a part of LDR file modules. The modules at that
must be exactly identical to the original ones in the drive. Step-by-step algorithm:
1. Switch on the power and start the pcmx_dsp.exe or pcmx_pkr.exe utility.
2. In the mode menu select the LDR-file loading option.
3. Load an LDR file in the Modules loader mode. If the loading procedure succeeds the drive will allow
operations with the firmware zone.
One difference of that method compared to drive switching to safe mode is expressed in the fact that during start
the drive is able to load the defects table and adaptive parameters from the firmware zone. Drive start in safe mode does
not accomplish that. That method will not work if modules having "A" importance are corrupt (see Table 2).
2. Drive start using the safe mode jumper setting.
During utility launch in safe mode you'll see the drive's factory alias. The method is recommended in cases, when
the drive "hangs during start" or does not start without the safe mode jumper.
1. Set the safe mode jumper (see PCB schemes in section 10).
2. Switch on the power and launch pcmx_dsp.exe or pcmx_pkr.exe utility.
3. If you work with a ROMULUS DSP or Poker hard drive run the Initialization from SA command (see para.
5.1.).
4. In the mode menu select the LDR-file loading option.
5. Load an LDR file in the Load ROM and modules. In case of successful loading the drive will spin up its
motor and report on readiness.
6. In case of ROMULUS DSP hard drives sometimes you have to suppress the Reset signal during utility launch
(see para. 5.1.).
7. Select the Standard mode from the mode menu. If during mode entry you see the Error loading modules
table! message, it means that an unsuitable LDR file has been loaded, drive hanging has occurred while
loading RAM copy or some problem with electronics/HDA has taken place.
[bg] Ta kakwo move da se naprawi sega - ne move da zaredi modulite ot samiq hard nito uspqwam da mu zaredq ldr fajl.
Ti kak si zaredil ldr fajla? Pri teb ima[e li go tozi problem da ne move da pro`ete softuera ot diska? [/bg]
-
29th May 2008 09:41 #8
-
29th May 2008 10:03 #9




Reply With Quote

, . , . () . . BIOS OS . . - . , 100% . "" 100-200 2.
- - 2 
05.05.23 ., 14:20 in