Results 1 to 15 of 15

Thread: 1700+ ,

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Registered User KoTaRaK's Avatar
    Join Date: Jul:2003
    Location: Sofia
    Posts: 129

    1700+ ,

    266 166 FSB PCI 41mhz . .

  2. #2
    acdc's Avatar
    Join Date: Jul:2001
    Location:
    Posts: 15,473
    ?
    Tbred - , 12.5 , , 100% .

  3. #3
    Registered User KoTaRaK's Avatar
    Join Date: Jul:2003
    Location: Sofia
    Posts: 129
    4 6 -

  4. #4
    Registered User entium's Avatar
    Join Date: May:2003
    Location:
    Posts: 1,426

    HOW TO EXECUTE, DETAILS OF MODIFICATIONS.
    See PIc to visualize Multiplier block diagram, bridges, and to locate all sockets/pins listed below.
    Changing an 8X Bit Value HI to a LO, to access 12.5X and lower from default Multipliers = 13X and higher.
    Tbred's rightmost 5th L3 bridge will be Open. Palomino's L10 bridge pair will be Open/Closed L to R.
    General solution is to ground that signal circuit. Options:-
    1:- Tbred, close the open 5th L3 bridge with a conductive trace around its open pit, no need to insulate the pit, restorable.
    2:- Palomino, change L10 bridge pair from Left/Right Open/Closed to Closed/Open.
    3:- Tbred and Palomino, connect AJ27 and nearby AH28 Vss/ground socket holes with fine wire u-loop, replace CPU.
    Or connect the "bases" of socket pins AJ27 and AH28 with conductive ink.
    4:- Tbred and Palomino, solder wire to socket AJ27, ground it thru 100 ohm resistor, (remotely switch/toggle).

    Changing an 8X Bit Value LO to a HI, to access 13X and higher from default Multipliers = 12.5X and lower.
    Tbred's rightmost 5th L3 bridge will be Closed. Palomino's L10 bridge pair will be Closed/Open L to R.
    General solution is to reset that signal circuit HI. Options:-
    1:- Tbred, open the closed 5th L3 bridge.
    2:- Palomino, change L10 bridge pair from Left/Right Closed/Open to Open/Closed.
    3:- Tbred and Palomino, connect AJ27 and nearby AH26 Vcc/Vcore socket holes with fine wire u-loop, replace CPU.
    Or connect the "bases" of socket pins AJ27 and AH26 with conductive ink. Note risk of accidental Vcore short circuit since no current limiting resistor as in 4:- below.
    4:- Tbred and Palomino, solder wire to socket AJ27, connect to Vcore thru 100 ohm resistor, (remotely switch/toggle).

    Palomino's open L1 bridges must be closed so pin/socket mods and mobo can connect to CPU's Multiplier signal circuits
    See picture
    EP43-DS3|E5200@3.33|ASUS EN9800GT HB /HTDI/ 512MB|2X2GB 800MHZ CL5 A-DATA|WD2500JB|NEC 4750A|BELINEA 1980S2

  5. #5
    Registered User KoTaRaK's Avatar
    Join Date: Jul:2003
    Location: Sofia
    Posts: 129
    , 6 10x wse pak

  6. #6
    Registered User entium's Avatar
    Join Date: May:2003
    Location:
    Posts: 1,426
    . .. .
    EP43-DS3|E5200@3.33|ASUS EN9800GT HB /HTDI/ 512MB|2X2GB 800MHZ CL5 A-DATA|WD2500JB|NEC 4750A|BELINEA 1980S2

  7. #7
    Registered User entium's Avatar
    Join Date: May:2003
    Location:
    Posts: 1,426
    EP43-DS3|E5200@3.33|ASUS EN9800GT HB /HTDI/ 512MB|2X2GB 800MHZ CL5 A-DATA|WD2500JB|NEC 4750A|BELINEA 1980S2

  8. #8
    Registered User KoTaRaK's Avatar
    Join Date: Jul:2003
    Location: Sofia
    Posts: 129
    4
    )

  9. #9
    Registered User entium's Avatar
    Join Date: May:2003
    Location:
    Posts: 1,426
    . . . . . .
    L1
    EP43-DS3|E5200@3.33|ASUS EN9800GT HB /HTDI/ 512MB|2X2GB 800MHZ CL5 A-DATA|WD2500JB|NEC 4750A|BELINEA 1980S2

  10. #10
    Registered User KoTaRaK's Avatar
    Join Date: Jul:2003
    Location: Sofia
    Posts: 129
    1 -
    ? all
    . 10x

  11. #11
    Registered User entium's Avatar
    Join Date: May:2003
    Location:
    Posts: 1,426
    . . .
    Last edited by entium; 15th August 2003 at 10:10.
    EP43-DS3|E5200@3.33|ASUS EN9800GT HB /HTDI/ 512MB|2X2GB 800MHZ CL5 A-DATA|WD2500JB|NEC 4750A|BELINEA 1980S2

  12. #12

  13. #13
    Child of the Darkness astral's Avatar
    Join Date: Jan:2003
    Location:
    Posts: 578
    Tbred- - Palomino 1700+
    THE ONLY WAY TO HAVE A FRIEND IS TO BE A FRIEND

  14. #14
    Registered User KoTaRaK's Avatar
    Join Date: Jul:2003
    Location: Sofia
    Posts: 129
    Palomino T-bred e 4 .

  15. #15
    Banned tony's Avatar
    Join Date: May:2003
    Location: blagoevgrad
    Posts: 1,265

    - :
    .
    U - - 1. - , .
    - .
    - . .

    Vcore 1,85.
    .

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Copyright © 1999-2011 . .
iskamPC.com | mobility.BG | Bloody's Techblog | | 3D Vision Blog |