Results 1 to 15 of 15
Thread: winxp Setup is starting Windows
Hybrid View
-
30th September 2008 15:40 #1Registered User
Join Date: Nov:2006
Location: sofia
Posts: 229
winxp Setup is starting Windows
winxp Setup is starting Windows.
, 2000 .
F5 -, .
TXTSETUP.SIF ACPI
Laptopa e Ascer Aspire 5020, winxp home windows.
, .
?
.. , ?
-
1st October 2008 08:48 #2Registered User
Join Date: Dec:2005
Location: yvr
Posts: 5,167
http://support.microsoft.com/default...;EN-US;q310760The following items can cause Setup to stop responding while the "Setup is starting Windows" message is displayed:
An incorrect mass-storage device (such as a SCSI or IDE controller) driver is being loaded, or the driver was not written for Windows and is not compatible. Contact the device's manufacturer or download the latest driver for the mass-storage device. For additional information, click the article number below to view the article in the Microsoft Knowledge Base:
216406 (http://support.microsoft.com/kb/216406/EN-US/) Specifying Third-Party Disk Controller Driver During Setup
There is a device connected to your mass-storage device that is preventing Windows from being installed. Remove any devices (such as scanners, tape drives, removable drives, and so on) from the mass-storage device controller. If the computer is IDE-based, verify that you have the master and slave designations set properly. If the mass-storage controller is SCSI-based, verify that the termination and bus speed is set properly.
The computer does not have the latest BIOS revision. Contact the computer's manufacturer or check the manufacturer's Web site. Many manufacturers have updated their BIOS revisions to properly support Advanced Configuration and Power Interface (ACPI).
An ACPI Hardware Abstraction Layer (HAL) is being used during Setup. Force the use of a non-ACPI HAL during Setup. For additional information about this procedure, click the article number below to view the article in the Microsoft Knowledge Base:...
-
1st October 2008 11:04 #3Registered User
Join Date: Nov:2006
Location: sofia
Posts: 229
ACPI,
- .
-
1st October 2008 19:13 #4Registered User
Join Date: Dec:2005
Location: yvr
Posts: 5,167
XP ?
-
1st October 2008 20:51 #5
, , "Setup is starting Windows". -. , , . , - , , , . , .
-
1st October 2008 21:42 #6Registered User
Join Date: Nov:2006
Location: sofia
Posts: 229
5 .
, +1, +2,
.
11 , - .
-
6th October 2008 16:46 #7Registered User
Join Date: Nov:2006
Location: sofia
Posts: 229
,
-
6th October 2008 19:26 #8Registered User
Join Date: Dec:2005
Location: yvr
Posts: 5,167
windows live CD- UBCD4Win, BartPE .
, . - - , , USB .
-
9th October 2008 14:05 #9Registered User
Join Date: Nov:2006
Location: sofia
Posts: 229
.
Live cd-tata
-
15th October 2008 09:30 #10Registered User
Join Date: Nov:2006
Location: sofia
Posts: 229
4 . , ?
: slack12.1 io scheduler cfq registered (default). 4 , noapic acpi=off nofb
edit2: slack 11 bare.i (kernel 2.4) "probing for usb controllers" nousb , bare26 ili test26 12,Last edited by khl86; 15th October 2008 at 15:37.
-
15th October 2008 20:26 #11Registered User
Join Date: Dec:2005
Location: yvr
Posts: 5,167
XP USB :
I386\txtsetup.sif ; :
USB [HardwareIdsDatabase]- USB\Class_03 = "hidusb" ....Code:[InputDevicesSupport.Load] ;usbehci = usbehci.sys ;usbohci = usbohci.sys ;usbuhci = usbuhci.sys ;usbhub = usbhub.sys ;usbccgp = usbccgp.sys ;hidusb = hidusb.sys serial = serial.sys serenum = serenum.sys ;usbstor = usbstor.sys
; , = "usb--", :
;PCI\CC_0C0320 = "usbehci"
;PCI\CC_0C0310 = "usbohci"
;PCI\CC_0C0300 = "usbuhci"
CD- . , ACPI .
txtsetup.sif, .
USB . 99% windows- a .
-
16th October 2008 10:28 #12
Join Date: Jul:2008
Location: Plovdiv
Posts: 17
, . 90% RAM.
-
22nd October 2008 14:42 #13Registered User
Join Date: Nov:2006
Location: sofia
Posts: 229
.
-
22nd October 2008 20:36 #14Registered User
Join Date: Dec:2005
Location: yvr
Posts: 5,167
, pcmcia, .
-
2nd June 2015 10:22 #15Registered User
Join Date: Jan:2013
Location: klisura
Posts: 7
usb support




Reply With Quote
R9 280,
7th May 2023, 21:28 in